If these tips do not correct your situation, a more serious problem may be the cause.
Call DriveSavers immediately to speak with a Recovery Advisor, and go to our Disaster Recovery page for further information on serious drive symptoms.
Click on the symptom you are experiencing to read our recovery advice.
1. The error message "Disk Boot Failure" appears during boot up.
2. The error message "Hard Disk(s) Fail (80)" appears during boot up.
3. The error message "Invalid Drive Specification" appears during boot up.
4. "Invalid Drive Specification" error on removable device or SCSI drive.
Indications
When your PC boots up, it runs a series of tests known as Power-On Self Test (POST). During this time, the system checks the operation of hardware such as video cards, memory and the hard disk. If a problem is found, an error message occurs and the system halts until the problem can be resolved.
The "Disk Boot Failure" message typically occurs when the operating system is trying to load into memory but cannot, because either the required system files are missing, or the hard disk that contained them isn't recognized.
Tips
Boot the system from a floppy and type "C:" at the prompt to locate your hard disk. If your hard disk is accessible, type "dir" and check the directory.
If it appears that the data is intact and the drive is reading properly, immediately copy your critical files to another storage media.
Once you're satisfied that all your data is backed up, run Microsoft's ScanDisk or Symantec's Norton Utilities. If no problems are found, simply reinstall the system software.
If the hard disk does not appear after booting up from a floppy disk, you should check the CMOS settings as described in the next section regarding error messages.
Indications
The system has potentially lost its CMOS settings. This is a common problem that frequently occurs, especially with older computers.
The CMOS (Complementary Metal Oxide Semiconductor) maintains the date and time settings as well as information about how your hard disk is set up. These settings are retained by a battery on the motherboard. When the battery dies, the settings are lost and the hard disk will become unrecognizable.
Tips
Most systems will allow you to enter the CMOS setup at start up time with a key stroke or two, such as [Del], [Esc] or [Cntrl]-[Esc].
Some systems, such as Compaq, NEC, Mitsubishi and many laptops and notebooks require a setup or diagnostic diskette to change the CMOS drive setting.
Once you enter the CMOS set up program, use the tab or arrow keys to jump to the appropriate field for drive settings and enter the correct settings for your drive.
It is a good idea to keep these settings on a note attached to your computer for future reference.
Most modern systems will let you "Auto" sense the drive. This will usually be successful. You should then reboot your PC.
Back up your system and get a replacement battery from your dealer.
Indications
The device driver may be damaged or the CONFIG.SYS file may have been changed.
Tips
- If you are familiar with editing your CONFIG.SYS file, open it in the editor and search for lines that look similar to: "DEVICE=ASPIDISK.SYS". If no such line exists, check the manual or "READ ME" file on your installation disk for the cartridge drive or SCSI Host Adapter manual.
- Try a "test" cartridge - one that is known to be good but holds no irreplaceable data.
- This will help you identify whether the problem is with the cartridge or the drive mechanism.
- If the same problem occurs with another cartridge check the SCSI cables and be sure they are firmly attached and the termination is correct.
- Isolating the drive on the SCSI bus by disconnecting other devices may also be helpful.
- With most systems, the first SCSI drive must have a SCSI ID of 0 (zero), and the first removable media drive must have a SCSI ID of 2.
WARNING: Tampering with a damaged disk may cause DATA LOSS! DriveSavers, Inc. and WWW.DATA-RECOVERY-TOOLS.NET make no guarantee to the accuracy of this information, and take no responsibility for the loss of data as a result of suggestions offered in this document.
NOTE: If you are unfamiliar with some of the terms on this page, see our Hard Drive Glossary.
[Above © DriveSavers Data Recovery. Reproduced by permission.]
